(1) CARRIER: PVC Pipe. (2) INSULATION: Polyurethane Foam (3) CASING: PVC or HDPE (4) BELL: Grooved PVC (5) CARRIER SEALING RING: Rubber (6) END SEAL: Compression Rubber NOMINAL PIPE SIZE (IN.) NOMINAL CASING SIZE (IN.) CARRIER O.D. (IN.) CASING O.D. (IN.) THICKNESS WEIGHT (LBS./ 20 FT.) FOAM (IN.) PVC CASING (IN.) 1 1/2 4 1.90 4.50 1.16 0.140 34 2 4 2.38 4.50 0.92 0.140 36 2 1/2 6 2.88 6.14 1.51 0.120 50 3 6 3.50 6.14 1.20 0.120 55 4 8 4.50 8.16 1.67 0.160 96 6 10 6.63 10.20 1.59 0.200 166 8 12 8.63 12.24 1.57 0.240 253 10 14 10.75 14.28 1.49 0.280 313 12 16 12.75 16.00 1.38 0.250 438 14 18 14.00 18.70 1.98 0.370 629 16 21 16.00 22.05 2.59 0.430 857 NOTE: Standard lengths are 20'-0". Weights are approximate. Consult manufacturer for HDPE dimensional data. SHORT FORM SPECIFICATIONS 1.1 All underground pre-insulated pipe 1 1/2” – 16” shall be Thermal Pipe Systems, Inc. Kool-Kore® piping with gasketed joints. 1.2 Carrier pipe shall be suitable for use at maximum hydrostatic working pressure of 160 psi at 73ºF. All core pipe must meet requirements as set forth in ASTM D2241 with standard dimension ratio SDR 26 and bearing National Sanitation Foundation seal for potable water pipe. 1.3 Each joint shall automatically provide for expansion and contraction through the rubber sealing rings placed in the groove of the integral bell. Pipe and fittings must be assembled with a non-toxic lubricant supplied by Thermal Pipe Systems. 1.4 Casing pipe shall be [Polyvinyl Chloride (PVC) meeting the minimum classification requirements of ASTM D-1784] or [High Density Polyethylene (HDPE)]. The thickness shall be in accordance with the Thermal Pipe Systems published data. 1.5 The insulation shall be polyurethane foam completely encapsulated on each end by a compression rubber end seal. 1.6 The rubber end seals shall be a compression rubber. 1.7 Fittings may be solvent weld or slip-on type PVC or ductile iron slip-on type. WARRANTY We warrant that our products are manufactured with the applicable material specifications and are free from defects in the workmanship and material using our specifications as a standard. Every claim under this warranty shall be deemed waved unless in writing received by Thermal Pipe systems, Inc. within (30) days of the date the defect was discovered and within (1) year of the date of shipment of the product. Thermal Pipe Systems, Inc. MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED, IN FACT OR IN LAW, INCLUDING WITHOUT LIMITATION THE WARRANTY OF MERCHANTABILITY OR THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN THE LIMITED WARRANTY SET FORTH ABOVE. LIMITATIONS AND LIABILTY It is expressly understood and agreed that the limit of Thermal Pipe Systems, Inc. liability shall be the resupply of a like quantity of nondefective product and that Thermal Pipe Systems, Inc. shall have no such liability except where the damage or claim results solely from the breach of the Thermal Pipe Systems, Inc. warranty. IT IS ALSO AGREED THAT THERMAL PIPE SYSTEMS, INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES FOR ANY ALLEGED NEGLIGENCE, BREACH OF WARRANTY, STRICT LIABILTY OR ANY OTHER THEORY, OTHER THAN THE LIMITED LIABILTY SET FORTH. ThermalPipeSystems,Inc. 5205 W. Woodmill Dr. Suite 33 – Wilmington, DE 19808 Tel: 302-999-1588 – Fax: 302-999-8861 Website: www.thermalpipesystems.com KOOL-KORE®